Robotic Wire Harness Manufacturing Machines

Solicitation No.

W51AA126QA040

Notice Type

Special Notice

Set-Aside

No Set aside used

Posted Date

March 19, 2026

Response Deadline

March 19, 2026

NAICS Code

532490AI guide

PSC / Class Code

W036

Contract Code

2100

Issuing Office

W6QK ACC-APG CONT CT TYAD OFC

Sub-Agency

DEPT OF THE ARMY

Agency

DEPT OF DEFENSE

Primary Contact

Deborah Belak

City

TOBYHANNA

State

PA

ZIP Code

18466-0000

AI Product/Service

both

NOTICE OF INTENT TO AWARD A SOLE SOURCE CONTRACT Army Contracting Command – Aberdeen Proving Ground (ACC-APG), Tobyhanna Division, Tobyhanna, PA 18466 intends to award a sole source contract to Molrix LLC, 106 Red Branch Drive, Madison, Alabama 35758-6657. This requirement is to lease one (1) Prototype/Low-Rate Initial Production (LRIP) Robotic Wire Harness Manufacturing Machine and lease one (1) Full Rate Production Robotic Wire Harness Manufacturing Machine, including machine documentation, software to operate, and engineering services for both pieces of equipment. The Government intends to acquire this service under the guidelines of FAR Part 12, Commercial Items and Simplified Acquisition Procedures. Only one responsible source, Molrix LLC, has been identified that can meet the Government’s specific needs for this requirement. Below are the parameters for the machines: Prototype/Low-Rate Initial Production (LRIP) Machine Robotic Capabilities: Power wire disposition (Insulated, Stranded, Bare, Coated) Data Wire disposition (Twisted Pair, Coax, Shielded) Terminations (IDC, Crimp, Poke home, Splice) Protection (Adhesives, Potting, Tape, Films, Clips) Mechanical Parameters: Machine Dimensions: 2.3m (L) x 2.2m (D) x 2.3m (H) Machine Weight: 2000 kg Axis Position Limits: 1500mm X Direction, 1050mm Y Direction, 750mm Z Direction, 240 Degrees B Direction, 360 Degrees C Direction Axis Velocity Limits: 1000 mm/s X Direction, 1000 mm/s Y Direction, 500 mm/s Z Direction, 20 rpm B Direction, 20 rpm C Direction Tool Change Positions Standard of 3 with an option of 10 positions Environmental Parameters: Operating Temperature: +10 Degree C Minimum and +35 Degree C Maximum Ambient Humidity: 5% Minimum to 85% Maximum Electrical Parameters: Voltage: 240V Maximum Current 32A Frequency: 50-60 Hz Phase: Single Pneumatic Parameters: Nominal Operating Pressure: 700 kPa Input Thread: G3/8 Filtration: Integrated into machine Full Rate Production Machine Robotic Capabilities: Power wire disposition (Insulated, Stranded, Bare, Coated) Data Wire disposition (Twisted Pair, Coax, Shielded) Terminations (IDC, Crimp, Poke home, Splice) Protection (Adhesives, Potting, Tape, Films, Clips) Mechanical Parameters: Machine Dimensions: 5.2m (L) x 3.0m (D) x 3.1m (H) Machine Weight: 6000 kg Axis Position Limits: 1500mm to Unlimited X Direction, 2500mm Y Direction, 350mm to Unlimited Z Direction, 240 Degrees B Direction, 360 Degrees C Direction Axis Velocity Limits: 1000 mm/s X Direction, 1000 mm/s Y Direction, 500 mm/s Z Direction, 20 rpm B Direction, 20 rpm C Direction Tool Change Positions Standard of 3 with an option of 10 positions Environmental Parameters: Operating Temperature: +10 Degree C Minimum and +35 Degree C Maximum Ambient Humidity: 5% Minimum to 85% Maximum Electrical Parameters: Voltage: 400V Maximum Current 32A Frequency: 50-60 Hz Phase: 3 Phase Pneumatic Parameters: Nominal Operating Pressure: 700 kPa Input Thread: G3/8 Filtration: Integrated into machine Both Machines will require the following: Documentation: Operators Manual Maintenance Manual Installation Documentation Training Material Software to Operate: Provide compatible software for Computer Aided Design (CAD) and Computer Aided Manufacturing (CAM) to support the equipment post processor Engineering Services: Operator and Engineering training Advanced operator training focused on production Application engineers and field support personnel Support equipment modification (End Effector Development) This is not a solicitation for competitive quotes. However, if any interested party can provide the Robotic Wire Harness Manufacturing Machines and related services, you may submit a statement of capabilities that may be considered by Tobyhanna Army Depot. A determination by the Government not to compete this proposed requirement is based upon responses to this notice and is solely within the discretion of the Government. Information received will be considered solely for the purpose of determining whether to conduct competitive procurement in the future. The capability statement and any other information furnished must be received via email only and must contain material in sufficient detail to allow the Government to determine if the party can meet the requirements. Capability statements and related materials shall be e-mailed to Deborah Belak at deborah.belak.civ@army.mil no later than 12:00 p.m. Eastern Standard Time on Friday, March 20, 2026.

1. March 19, 2026Posted Date
2. March 19, 2026Proposals / Responses Due